Technical lighting partner for professionals Contact us
Enquiry0
Produktbild av LTECH SE-10-500-1000-W1D

LED Driver CC 500-1000mA 10W DALI-2 IP20

CC · 500–1000 mA · 10 W · DALI / DALI-2 / Push DIM · NFC Lighting, 1 mA steps · IP20

Input voltage
100-240 V AC
Output voltage
2-12 V
Output current
500–1000 mA
Max. power
10 W
Control
DALI, DALI-2, Push DIM
DALI device type (DT)
DT6
IP rating
IP20
Dimensions
135 × 30 × 20 mm

DALI-2 control also works in DALI systems. Available functions depend on the controller.

Logga in för pris och orderförfrågan

SKU: SE-10-500-1000-W1D Category:

Description

LTECH SE-10-500-1000-W1D is a constant-current LED driver with an adjustable output current of 500–1000 mA. Control: DALI / DALI-2 / Push DIM. The maximum output is 10 W.

Set the output current with the NFC Lighting app in 1 mA steps. Disconnect power to the driver before programming, select a current suitable for the LED module and write the setting via NFC. The app configures parameters; everyday dimming uses the driver’s stated control interface.

Check the LED module’s rated current and voltage requirement at full brightness. The Technical specifications tab lists the voltage range at each current and calculated load power: P = I × U. The lower voltage limit describes a compatible LED load, not minimum dimming. The driver’s maximum output limit still applies where a rounded voltage row produces a slightly higher calculated value.

ModelSE-10-500-1000-W1D
Output typeConstant current (CC)
Output current500–1000 mA
Output voltage range2–12 V DC
Maximum output10 W
Channels1
ControlDALI / DALI-2 / Push DIM
DALI device typeDT6
Current settingNFC Lighting, 1 mA steps
Input voltage100-240 V AC
Dimming range0–100%
Minimum stated dimming level0.01%
Ambient temperature ta-20–50 °C
Maximum case temperature tc80 °C
Dimensions (L × W × H)135 × 30 × 20 mm
Net weight80 ± 10 g
IP ratingIP20
Standby after off command<0.5 W
ProtectionOvertemperature, overload, short circuit
LTECH SE-10-500-1000-W1D – documented settings and power from stated voltage · Set current / Output voltage at full brightness / Calculated power at voltage limits
Set current: 500 mAOutput voltage at full brightness: 2–12 VCalculated power at voltage limits: 1–6 W
Set current: 550 mAOutput voltage at full brightness: 2–12 VCalculated power at voltage limits: 1.1–6.6 W
Set current: 600 mAOutput voltage at full brightness: 2–12 VCalculated power at voltage limits: 1.2–7.2 W
Set current: 650 mAOutput voltage at full brightness: 2–12 VCalculated power at voltage limits: 1.3–7.8 W
Set current: 700 mAOutput voltage at full brightness: 2–12 VCalculated power at voltage limits: 1.4–8.4 W
Set current: 750 mAOutput voltage at full brightness: 2–12 VCalculated power at voltage limits: 1.5–9 W
Set current: 800 mAOutput voltage at full brightness: 2–12 VCalculated power at voltage limits: 1.6–9.6 W
Set current: 1000 mAOutput voltage at full brightness: 2–10 VCalculated power at voltage limits: 2–10 W
NFCYes

Technical details

The details for your installation

Constant-current LED driver for 500–1000 mA, up to 10 W, with DALI, DALI-2, Push DIM control.

Check connections, load and mounting instructions in Ltech’s original datasheet before installation.

Open Datasheet (PDF)
135 mmSE-10-500-1000-W1DTOP VIEWSIDE VIEW30 mm20 mm
Dimension drawing · 135 × 30 × 20 mm · schematic

Constant current · SE-10-500-1000-W1D

Current, voltage and available power

Set the LED module current using the NFC Lighting app or LTECH NFC programmer. Available power depends on the permitted output voltage at that current: W = V × A. The rated wattage is not available at every current setting.

The table describes the LED load at full brightness, not the lowest dimming level. Power follows current × voltage; also check the driver rating and original datasheet before selecting a load.

Related products